Error 0006 starting REBUILD.

ok, I never will mention DVDSHRINK again. It was my dissatisfaction with the movie I compiled that forced me to search for an alternative and so I found it with DVDREBUILDER. By the way I didn't interrupt the proces, as far I know. But the strange thing is, that I switched back to Quenc 54 instead of 59A and got no errors anymore, but disabled all quality options this time ! I'm now burning my first RW with my difficult movie !! Thx for answering, just a starter on DVDRB and I'm glad for the alternative for DVDSHRINK. But let first see the results ! Toine

I just read a tread that I think mentioned frame loss with QuEnc 0.59 -- but I can't remember where.. Mention DVD Shrink all you want. It is a very good product written by a very smart guy... I use it for lots of functions -- just not reencoding DVDs. I am very quality conscious -- if I didn't care about quality I'd use VHS to make backups.

Somewhere I'd mentioned .58 as the last stable version -- actually what I'd intended to say was .57... I've done a lot of testing with that version and it works well.

As I mentioned above, stick with 0.57 until the bugs are worked out of .59 -- unless of course you are purposely attempting to identify problems for the QuEnc version. But... if you are trying to look for DVD-RB bugs, please use 0.57 (actually as I recall .54 was a good one too, but I'm not positive)-- as with the newer version it becomes difficult to decide where the source of the problem might truly be (DVD-RB is also in testing) or QuEnc.

Thanks for the quick response. I would use the 57 version if I could find it. :( If you would want any help or info on the problem with the 59a version of QuEnc and DVD RB please let me know what I can do to help you. As I said I can run either very easily. On this subject would it help if I created a test image consisting of 30 seconds of each chapter I also use DVDReMakePro and It will do this I then could run the two thru QuEnc and DVDRB and see what happens? What do you think?

QuEnc 0.57 is available to download on keep it UP

Thanks Rockas I am doing some tests, I am right now doing a test for a baseline using .54 version of QuEnc and DVD Rebuilder .69 (Beta) I used dvdremakepro to get 60 seconds from all chapters of the Matrix I will run this same source using QuEnc .54 then .57 and finally .59a I will post the rebuilder.log file and output / working folder information for tests. Anything else you would like we to save for each test?

I got error #6 when I used quenc 0.59 so I downgraded to 0.57 and did the whole transcoding again. I still got the same error. What now? I'm using avisynth 2.54 and dgdecode.dll. Have I forgot some information? The movie is Terminator 3 if that makes any difference at all. Regards, M7S

I just did 4 full encodes of "Rundown" as a test overnight. CCE v2.50: Success QuEnc v0.54: Success QuEnc v0.57: Success QuEnc v0.59: Error 006 and an ungraceful exit I'll run it again and do some analysis of the QuEnc output to see if I can put my finger on the problem.

After about 16 hours of attempting to process disc one of Yes, Minister I got this 0006 error. Apparently the QuEnc version DVD-RB Installer loaded is 1.0.0.1 - should I try to go back to a previous version of QuEnc? I have DVD-RB v.70 and AVISynth 2.5.5.0. Mmm, might be relevant - when I tried using ReJig (v0.3.0.0) to process this disc first, DVD-RB worked, but when I went to burn the backup Nero gave me a message about the DVD source files were out of standard and might not work/play properly (I can't remember the exact wording, sorry). That's why I tried QuEnc....and ended up here now. Any input greatly appreciated, thanks - I hope I'm providing enough info for you folks! EDIT: Just realized some more info might be helpful - I used DVDDecrypter v3.5.2.0 to rip the entire disc, in File mode, to an external HDD. I have DVD-RB working on the internal drive but getting the source material from the external HDD and outputting to the HDD.